I need a final drive belt

[Nomad2day]

I know the belt is 1 1/8th inch wide. What is the pitch and number of teeth I need for a 2007 Bulldog? Where to order from? The manual appears to be worthless here, only states 1 1/8th.
Mine has a good nick in it and needs replacing...
Thanks in advance for any info
Neil

Page 64 of 2008 Performance Guide by S&S Cycle
1958-2008 50th ann iversary s&s®/gates® high strength final drive belts how many final drive belts have s&s engines broken yes a lot of power can break things so what s the solution the solution that we are offering is stronger belts s&s has teamed up with the gates® corporation a leading manufacturer of power transmission belts to offer a series of secondary drive belts for many popular v-twin models these belts feature gates super strong x3n carbon cord material which is significantly stronger than the aramid material used in many oem final drive belts s&s final drive belts by gates are available with 14mm pitch in 11/2 and 11/8 widths see the chart below and match the width and number of teeth required for your vehicle you can find this information in the vehicle service manual 106-0361 secondary drive belts 14mm pitch teeth 125 126 127 128 130 132 133 135 136 139 11/8 wide 106-0357 n/a n/a 106-0358 106-0359 106-0360 106-0361 106-0362 n/a 106-0363 msrp $164.95 * * $164.95 $164.95 $164.95 $174.95 $174.95 * $174.95 11/2 wide n/a 106-0348 106-0349 106-0350 106-0351 106-0352 106-0353 106-0354 106-0355 106-0356 msrp * $174.95 $174.95 $174.95 $174.95 $174.95 $177.95 $179.95 $179.95 $184.95 email us at sscust@sscycle.com 64

 

[Raywood]

When my tranny sprocket nut came loose a couple years ago it caused a deep grove in my belt. But that belt has lasted a long time and it didn't cause any weakness that I know of. Of course replacing it is the safe bet but I would just say that that belt is awful strong and my still give you many miles.

 

[alhall88]

Neil can you still read the number on your old belt? I can read the writing still on my belt. Mine is a gates 1-1/2 wide and 130 tooth. There is also a part number which can be cross referenced with the S&S belt if you look at the gates belts.

 

[Nomad2day]

Neil can you still read the number on your old belt? I can read the writing still on my belt. Mine is a gates 1-1/2 wide and 130 tooth. There is also a part number which can be cross referenced with the S&S belt if you look at the gates belts.

Al,
I rotated the belt all the way around and the only stamping or lettering on it said "Big Dog Motorcycles". Now there is some information I can really use when I go to replace it.....
I will look again tonight when I get home or physically count the teeth...

Raywood,
Belt is below....I think it is ready to be replaced.

 

[Nomad2day]

I laid out there tonight on the floor and counted the teeth a few times...
Came up with 133 teeth twice anyway but will try again in the morning when I am sober....
Dang, found a few other gashes in the belt too. If you havent checked your lately you might want to run you hand along it one time..
Neil

 

[WB Cycles]

Neil it IS a 133 tooth belt. (BDM120-00529) and is the same for the following bikes:
BULLDOG - 2005 , 2006
BULLDOG EFI - 2007
CHOPPER - 2006, 2007
CHOPPER RT - 2005
CHOPPER BDM - 2005
CHOPPER DAYTEC - 2005
K9 - 2008, 2009
K9 BDM - 2006, 2007
K9 BDM SPECIAL EDITION - 2007
K9 SPECIAL EDITION - 2008
K9 DAYTEC - 2006, 2007
K9 EFI - 2008, 2009
K9, CHR PKG - 2009
K9, EFI, CHR PKG - 2008, 2009
MASTIFF - 2005, 2006, 2007, 2008, 2009
MASTIFF, CHR PKG - 2008, 2009
MASTIFF, EFI - 2008, 2009
MASTIFF, EFI,CHR PKG - 2008, 2009
MASTIFF, SP ED - 2008
MUTT -2008
PITBULL - 2005, 2006, 2007
RIDGEBACK - 2005, 2006

 

[TCALZ06]

How many miles should our belts last?

 

[Nomad2day]

How many miles should our belts last?

I don't know. Mine got knicked somehow. I did get one from a forum member here. This place rocks...
Neil

 

[Little-Boo]

I know the belt is 1 1/8th inch wide. What is the pitch and number of teeth I need for a 2007 Bulldog? Where to order from? The manual appears to be worthless here, only states 1 1/8th.
Mine has a good nick in it and needs replacing...
Thanks in advance for any info
Neil

Page 64 of 2008 Performance Guide by S&S Cycle
1958-2008 50th ann iversary s&s®/gates® high strength final drive belts how many final drive belts have s&s engines broken yes a lot of power can break things so what s the solution the solution that we are offering is stronger belts s&s has teamed up with the gates® corporation a leading manufacturer of power transmission belts to offer a series of secondary drive belts for many popular v-twin models these belts feature gates super strong x3n carbon cord material which is significantly stronger than the aramid material used in many oem final drive belts s&s final drive belts by gates are available with 14mm pitch in 11/2 and 11/8 widths see the chart below and match the width and number of teeth required for your vehicle you can find this information in the vehicle service manual 106-0361 secondary drive belts 14mm pitch teeth 125 126 127 128 130 132 133 135 136 139 11/8 wide 106-0357 n/a n/a 106-0358 106-0359 106-0360 106-0361 106-0362 n/a 106-0363 msrp $164.95 * * $164.95 $164.95 $164.95 $174.95 $174.95 * $174.95 11/2 wide n/a 106-0348 106-0349 106-0350 106-0351 106-0352 106-0353 106-0354 106-0355 106-0356 msrp * $174.95 $174.95 $174.95 $174.95 $174.95 $177.95 $179.95 $179.95 $184.95 email us at sscust@sscycle.com 64

You may want one of this babies, being that you are going to get one

http://www.bigdogbiker.com/forums/p...l-drive-belts.html?highlight=final+drive+belt


Carlos :2thumbs:

 

[BrianLo]

Damn belt cost me more than double what the front pulley cost!