knothead
Second Chance Customs
I have a RIP harness on the shelf...I will look for it this evening
Fried something
- Thread starter cgaroutte1201
- Start date
Mikeinjersey
Well-Known Member
You seem pretty capable . Maybe you could consider an M-Unit
cgaroutte1201
Member
Had I just not paid for that RIP kit I probably would have.
cgaroutte1201
Member
I appreciate you checking for me. I'll have to wait until BDM gets one in stock.
cgaroutte1201
Member
I seen that you had a an 05 harness for a chopper on eBay. I would imagine it's probably shorter but I could always buy me some wires and some JST connectors and make them longer if needed. Donna advised that they're currently out of 06 K9 harnesses, however she did say that someone bought a shorter harness and is going to make what he needed longer and that he would let her know how it goes. She said they plan on making more harnesses for my bike but it would be awhile.
I don't wanna wait but will have to if it's in my best interest.
knothead
Second Chance Customs
If you already bought a rip kit controller then the harness I have forsale wont work on that controller...my harness is the factory style harness that works with the original ehc or the axel ehc that wildsteedworx sells...which most of us run the axel ehc and that's what I run in all my bikes
cgaroutte1201
Member
The RIP uses the D-sub connector, isn't that what the original wiring has in these bikes?
Attachments
knothead
Second Chance Customs
Yeah I wasnt thinking cause there is rip kit gen 1 and a rip kit gen 2...one kit does use the original d connector and the other one doesnt.
cgaroutte1201
Member
Mine has the Thunder heart ignition module. Idk if that's different than what harness you have.
Attachments
cgaroutte1201
Member
Oh ok, yeah I got the Gen 2 that does use it. I'm glad I picked the right one when I bought it lol.
knothead
Second Chance Customs
That's the same ignition module on all 05 and up models. If you want this harness I will sell it for 325.00 here on the forum instead of the 380 I have on ebay...ebay charges 14.7 % fees..llet me know if you want it and I will locate it where i put it and send you a pm where we can exchange information
cgaroutte1201
Member
Right on, and I appreciate it.
I may need to do that. I'm curious as to how much shorter it may be than the K9 harness. I can always solder some longer wires on and heat shrink em. It'll be a Frankenstein style setup but I'm thinking I can get it done.
mastiffdave
Well-Known Member
Just bite the bullet and let Knotthead fix/build/ whatever you need to get your bike running. it will be the cheapest money you ever spent to do it right. I was so disgusted with mine I was ready to push it off a mountain and he fixed all the other people’s f$$k ups and it’s reliable as heck now.
cgaroutte1201
Member
Right! I was about to take mine to a guy about 3 hours away before I found out that the wiring harness I have was the warranty fix BDM used when the original charging system was knocking out their ECM's.
Unfortunately my whole wiring system is obsolete. So now I'm forced to go back to the original backbone harness but use the RIP Gen 2 kit which comes with the power harness and new ECM.
I think once I get that backbone harness, I may need to make a few wires longer as it's for the chopper and a little shorter than the K9 harness. Which is fine and I can do that, but I just wish BDM had them in stock and I wouldn't need to do any of that.
However after all said and done, I'll have an extra power harness if anyone will ever need it. It's definitely been a learning experience, but a good one.
cgaroutte1201
Member
And if I can't fix it, Knothead will be getting a call lol.
cgaroutte1201
Member
knothead
Second Chance Customs
Your thinking about KFC and not EHC
