Easiest clutch lever pull
- Thread starter EZ Dog
- Start date
BigDogBro1
Made in the USA
I have a BDM Easy Pull clutch system. It pulls half as hard than stock. The kit mades changes to the clutch pack, reducing the plate count from 13 to 9 and replaced the ball ramp system. I think the kit cost around $400.00 plus installation cost. The clutch performance seems to be equivilent to the stock 13 plate system but I ride normal. 10k miles thus far.
Last edited:
Nukeranger
Nukeranger
I don't get it. My clutch is stock and not hard to pull.Maybe I ride too much.
BWG56
Guru
thats because your left handed:roll:
Maybe I ride too much.
Nukeranger
Nukeranger
:2thumbsamn, busted You're pretty darn smart for figuring this one out.
amn, busted You're pretty darn smart for figuring this one out.
nine lives
Active Member
If you grease your ball and ramp, lube your cable and lever, maybe eat some Wheaties, you should be good to go.
jimizee028
TRUE COLORS COLLISION
I installed the newer version ball and ramp....easy pull....and its considerably alot easier to pull,course I didnt add the new clutch packs and if I get on it it slips.....but all in all its alot easier on the left hand
A
adamthisis
Guest
Get the Bandit clutch, I put in the BDM easy pull kit in and it only lasted about a year, and was slipping in every gear. Couldn't even give more then a quarter throttle, and it would slip. Put the Bandit in about 6 months ago, haven't had one problem since. Shifts in to gear like butter, goes right into neutral at a stop, before I had to give it gas. Plus I think the pull is easyer then the BDM easy pull.
BWG56
Guru
X2 however mine don't slip, I'd say its about 25 percent easier.
jimizee028
TRUE COLORS COLLISION
If you put the Bandit Clutch in there are you supposed to go back to the stock ball and ramp or leave the ''easy pull'' ball and ramp in there?
pknowles
RETIRED
Tennis ball is the answer. Get the cheap ones from Wally World, as they work just as good as the expensive ones. Get up in the morning, place it in your left hand and start your work out. Easy to travel with too. You will be surpirsed after about a month of practice.Oh yea, let us know when you bust the first one!
Black Rider
Active Member
I am fresh at this. Do you know the part number or contact for a full kit with everything I will need?Get the Bandit clutch, I put in the BDM easy pull kit in and it only lasted about a year, and was slipping in every gear. Couldn't even give more then a quarter throttle, and it would slip. Put the Bandit in about 6 months ago, haven't had one problem since. Shifts in to gear like butter, goes right into neutral at a stop, before I had to give it gas. Plus I think the pull is easyer then the BDM easy pull.
Also how difficult is the install? I am in Italy and hopefully the local Harley shop can install but I like to know before what the process is so they can not try any bull!! Thanks in advance.
A
adamthisis
Guest
Go to banditmachineworks.com the clutch pack for Bigdogs is called the Brusier. Look up that, I didn't install it had a shop do it. Good luck trying to get a Harley dealership do it, the ones around my area won't even look at my bike, let alone touch it. I would just call Bandit and talk with them about what you will need.
ITALIANCHOPPERS
New Member
i have a amp power cluch.used.if i find tomorrow you can have for 50 and try it out
‘AMP’ Power Clutch | 500-409 | J&P Cycles
has for 115
and if you dont like it i can help set u up hyd
‘AMP’ Power Clutch | 500-409 | J&P Cycles
has for 115
and if you dont like it i can help set u up hyd
Black Rider
Active Member
Went to bandits. I will also call.
The amp sounds interesting too but I have not found any big dog info on it. Will it fit? Most info I found was for Harley.
The amp sounds interesting too but I have not found any big dog info on it. Will it fit? Most info I found was for Harley.