DYNO #'S ARE IN!
- Thread starter Chopper117
- Start date
MARV
Well-Known Member
You gona break some shit now!!!
aint that the truth!
my kickstand was my latest victim.
GONE
seatmaker
Well-Known Member
I'll take 2No thanks but this could work!:roll:
damm I'd just like to have 1.....2 bitches cost to much..I'll take 2
alhall88
UAW
You need one? got my old stock one laying around if you want it.
MARV
Well-Known Member
hell yea! a chunk of 4x4 doesnt fit in my pocket too well
no stands on ebay now.
i still have the bracket just missing the stand and pivot hardware.
your pm aint working
toadstool
Active Member
Umm, just curious as to how the hell does one loose a kick stand?
Were you going so fast it flew off?
MARV
Well-Known Member
Umm, just curious as to how the hell does one loose a kick stand?
Were you going so fast it flew off?
it shakes
it rattles
but it ROLLLLLS :up:
Chopper117
Chopper Nutt
Chopper117
Chopper Nutt
We had a little delay on getting my bike back. :bang:
As Frank was dyno'ing the bike he said he had a hard time getting it into 1st, 2nd, and third gear so he went ahead and pulled apart the trans and they figured since there was a service bulletin out for the countershaft washer replacement they figured that could be the problem. But after he pulled the trany apart he saw that the countershaft walked and got stripped. So they are seeing if Big Dog will cover this since this service bulletin has been out for quite a while for the washer being replaced.
So I'm hoping they will cover it or else it will cost me over $1000 to get it done. :bang: So that's where I stand now! Waiting for a phone call! Here is a picture of the housing and you can see where the arrow is pointing is where it stripped.
C
chaingunner
Guest
We had a little delay on getting my bike back. :bang:
As Frank was dyno'ing the bike he said he had a hard time getting it into 1st, 2nd, and third gear so he went ahead and pulled apart the trans and they figured since there was a service bulletin out for the countershaft washer replacement they figured that could be the problem. But after he pulled the trany apart he saw that the countershaft walked and got stripped. So they are seeing if Big Dog will cover this since this service bulletin has been out for quite a while for the washer being replaced.
Here is a picture of the housing and you can see where the arrow is pointing is where it stripped.
View attachment 3339
WOW that blows! Hope they cover it!
BD is watching! FIX THIS FOR THIS FINE FELLA!!!:2thumbs:
These trannies have a hard enough time staying together with stock power. That's one of the many reasons my bike is stock except for a .600 cam and extended filter. I just don't think these bike were engineered for this much extra power. I'd rather ride than wrench. I get plenty of wrench time on my race car. :loony:
Chopper117
Chopper Nutt
yea sucks for sure but better now while its there.
mine is just a matter of time. while upshifting sometimes it will find neutral.
still got stock clutch, tranny and ehc though.
Yea that's what I said...I could of been in a worst situation like stranded some where!
MARV
Well-Known Member
well was warming up my bike tonight for the ride home. lets not forget i dont have a kickstand. a couple of blocks of firewood was holding it up since i got there. go inside to gear up and dont you know the bike goes over. mirror stem broke, headlight dented and glass broke, but light still worked, left rear blinker cover busted. guys all worried and concerned waiting for my response....
i was happy i still had a headlight! :up:
i was happy i still had a headlight! :up:
yea im kidding.
didnt go out to see my buds.
instead i stayed home and polished the bike.
Damn!!!!
I was ready to start packing up some stuff to send you.:lol::lol::lol: