Yellow Bitch Down, Need Bearings.

[Marky-Marc]

Item 28,29 and 30, 1" bore

View attachment 31464

Yup,.....just need the width of the spacers and I can, or WE can get them for him.....and @BWG56 my picture is better than YOUR picture...nany nany boo boo....BWAHAHAHAHAHA

 

[BWG56]

Yeah but I bet you don't have this shit, nanny nanny boo hoo.
These are the spacers and length in my Mastiff with a 300 tire, what do you have to say about those apples Markywho's your daddy now

 

[Marky-Marc]

Yeah but I bet you don't have this shit, nanny nanny boo hoo.
These are the spacers and lenght in my Mastiff with a 300 tire, what do you have to say about those apples Markywho's your daddy now
View attachment 31466

You are my daddy....you are my daddy......now we're getting KINKY.....I have them NOW...and so does @francoblay1, if he gives me the go ahead, I'll go get him some locally or order some......PRICELESS......I know you RAN out to the garage and just did that cuz of my nany nany comment...bwahahahahaha

 

[BWG56]

Was the calipers calibrated before using .beats trying to remember where they went​

That's freakin hilarious that you would ask this

 

[Th3InfamousI]

That's freakin hilarious that you would ask this

View attachment 31468

I can't find my rear spacer lengths. Found the front though, but that's off no use.

I mean I guess you could bang up the spacers but the wheel woulda been wobbling like crazy if you lose bearings and beat the spacers

Sent from my 831C using Tapatalk

 

[Th3InfamousI]

Spacers shouldn't be damaged as they ride in the inner race and are jammed up against the squish tube.

His axle nut came loose he said...

Sent from my 831C using Tapatalk

 

[francoblay1]

Correct, the spacers ARE damaged!!!! I need confirmation on those measures.

@BWG56 Bro you are pretty close on your drawing.... can you confirm it and re.write it again a little bit better, please? I will send your pic to my mechanic.

He will make new ones... Inox he said. (your thoughts?)

 

[Th3InfamousI]

Tough to see but that right spacer looks fine. Need to see them cleaned up. The only one that may have been beat up looks like outside left one. But still hard to see.

Mechanic should be able to measure them. I'm confused

Sent from my 831C using Tapatalk

 

[HMAN]

Hey Franco, give a shout to Matt. As they ARE making Dogs again, he may have some NEW parts that would fit the bill?

 

[francoblay1]

You are my daddy....you are my daddy......now we're getting KINKY.....I have them NOW...and so does @francoblay1, if he gives me the go ahead, I'll go get him some locally or order some......PRICELESS......I know you RAN out to the garage and just did that cuz of my nany nany comment...bwahahahahaha

Well.... that would be awesome. I think it will save me some headaches.... PM with $$$$ numbers, please. Thank you Bro.

 

[francoblay1]

Tough to see but that right spacer looks fine. Need to see them cleaned up. The only one that may have been beat up looks like outside left one. But still hard to see.

Mechanic should be able to measure them. I'm confused

Sent from my 831C using Tapatalk

Apparently the spacers have lost some body material from running awkward due to the bearings failure.... he recommends new ones or will not insure the final result.

 

[BWG56]

If you don't get them shipped from over here, give him my sketch and along with what is left of yours he should have enough information, it also looks like your axle has been chewed up also, might want to think about replacing that also

 

[BWG56]

I missed that.

And this from the guy that always says clean n tight, MY ASS

 

[chubs]

If you don't get them shipped from over here, give him my sketch and along with what is left of yours he should have enough information, it also looks like your axle has been chewed up also, might want to think about replacing that also

Good eye!

 

[HMAN]

And this from the guy that always says clean n tight, MY ASS

I can't recall Franco ever saying his ass was clean n tight.....lol!

 

[chubs]

I can't recall Franco ever saying his ass was clean n tight.....lol!

 

[BWG56]

Fukin Wanker, make me a drawing, make me a drawing

 

[francoblay1]

Fukin Wanker, make me a drawing, make me a drawing
View attachment 31485

Awesome, my mechanic asked for your phone number too!!!

Thank you Bro.

 

[francoblay1]

I can't recall Franco ever saying his ass was clean n tight.....lol!

 

[BWG56]

Awesome, my mechanic asked for your phone number too!!!

Thank you Bro.

Anytime, and what does he look like, is he hot?