flashing lights no pwr

[mr big dog]

hey guys i got a 05 ridgeback the hazards are flashing when I have the key on and when I hit the run button the headlight flashes the bike will not start at all I put a brand new battery 350 cca checked all wires and I cannot find a crack or any corrosion on wires I think the ecm or the ehc is bad what do you guys think how can I tell if the ecm is bad what exact lights need to be on the ehc in order for it to run

 

[BWG56]

I know you put new battery in but did you charge it before you installed it? Maybe you need it load tested to make sure its good first and check this out also
Your Introduction

 

[BWG56]

damnit u musta replied wile I was still typing

He who hesitates, looses use more than 1 finger to type

 

[Marky-Marc]

Here you go, same bike, same symptoms, was the battery.....

http://www.bigdogbiker.com/threads/wont-start.11303/

 

[mr big dog]

sorry guys
yes I bought 2 new batteries had 1 charging all night and the other I had installed in the bike to check the wiring I switched them this morning and still nothing when I turn the key the hazards flash no crank no head light nothing but flashing hazards when I hit the run switch the headlights flash and when I let it go it turns off I have the bike taken apart and I still have no idea ill post a picture of the lights that are on the ech

 

[mr big dog]

first is the ech that's all the lights that light up the green light blinks
second is the hazards no headlight on
third is the volts of battery 12.8
forth is the load test 10.8

 

[Marky-Marc]

looks like the new battery is weak!

What is the voltage reading when you hit the start button? You need to test the load on the battery......

Other thing you may try, is reset your ECM....take the positive and negative cables OFF the battery and hold them together with no power for about 20-30 seconds.

You could try to jump start it, however, when JUMPING it, do not have the OTHER vehicle running...basically it's just using the voltage from another battery to jump start it.

JUST DO NOT HAVE THE OTHER VEHICLE YOU ARE USING TO JUMP your DOG Running or even turned on!!!!

 

[Marky-Marc]

.more and more cops all the time. Can't sneak anothing by now

who and where are the 5-0's???

bwahahahaha

 

[BWG56]

If you load tested it correctly and that's the result, the battery is no good

 

[BWG56]

who and where are the 5-0's???

bwahahahaha

I know you put new battery in but did you charge it before you installed it? Maybe you need it load tested to make sure its good first and check this out also
Your Introduction

Wanker blew me off, what the WTH, I'm done

 

[Marky-Marc]

Wanker blew me off, what the WTH, I'm done

There should be a way to make people do an intro before signing up somehow......oh well......

 

[Marky-Marc]

If you ARE @mr big dog, please do THIS and go HERE!

It shows respect and introduces you to all of us in the BDB community....

Hope that helps ya @BWG56.......

 

[BWG56]

There should be a way to make people do an intro before signing up somehow......oh well......

 

[BWG56]

If you ARE @mr big dog, please do THIS and go HERE!

It shows respect and introduces you to all of us in the BDB community....

Hope that helps ya @BWG56.......

I always need help.

 

[mr big dog]

What is the voltage reading when you hit the start button? You need to test the load on the battery......

Other thing you may try, is reset your ECM....take the positive and negative cables OFF the battery and hold them together with no power for about 20-30 seconds.

You could try to jump start it, however, when JUMPING it, do not have the OTHER vehicle running...basically it's just using the voltage from another battery to jump start it.

JUST DO NOT HAVE THE OTHER VEHICLE YOU ARE USING TO JUMP your DOG Running or even turned on!!!!

the start button doesn't work nothing works on the bike at all only flashing hazards lol the one thing I didn't do I try and reset it that way with the positive and negative cables but I also do have a car battery next to the bike just using the voltage on it but iwill try and reset the ECM and let you kno w

 

[mr big dog]

I always need help.

sorry guys what into do I need I'm new to this stuff I don t wanna be that ass hole

 

[Marky-Marc]

the start button doesn't work nothing works on the bike at all only flashing hazards lol the one thing I didn't do I try and reset it that way with the positive and negative cables but I also do have a car battery next to the bike just using the voltage on it but iwill try and reset the ECM and let you kno w

DO AN INTRODUCTION NOW!

 

[BWG56]

If you ARE @mr big dog, please do THIS and go HERE!
....

 

[Marky-Marc]

Bwahahahaha.....click the link above under HERE and THIS @mr big dog.......

 

[RRRUFF]

Make sure all your connections are clean and tight. Check your ground connection at the starter mount. And as said above you got to have at least 12.8 volts. Load testing on these don't always tell the truth. You may have a bad ehc but check the simple things first. I think Captin America/Curtis/Wild Steed Worx can test ehc.