2006 K-9 Docs ESC / Carb

[mchllacey]

Does anyone have a pinout and or wire diagram for this ESC ? It was on the bike when I bought it and has some minor problems I'd like to fix. THX in advance.
If this post is something I shouldn't have posted ( copyright etc. plz remove it if you have that ability.

 

[mjsk9]

Do you have the Service Manual? Electrical is in Chapter 6. Compliments of bdm7250....

Manuals >>> https://www.dropbox.com/sh/4342373flodnbhj/AACDvhA93EOHPPKCs2gYPQDPa?dl=0anualsan
Like Reply

 

[pauldeepsea]

I have one, I will scan it and send it to later today . Just let me know If someone else gets it to you before I do.

Does anyone have a pinout and or wire diagram for this ESC ? It was on the bike when I bought it and has some minor problems I'd like to fix. THX in advance.
If this post is something I shouldn't have posted ( copyright etc. plz remove it if you have that ability.

 

[pauly]

I believe the OP asked for pinout and or wire diagram for Doc,s ESC . Big Dog's might be a bit different.

Paul.

 

[pauly]

My message is awaiting moderator approval, and is invisible to normal visitors.

 

[Th3InfamousI]

Check out this thread bith rip and esc use the same thunderheart unit. You can go to their support page for wiring diagrams

Rip Gen1 wire diagram

I have a 08 K9 put the RIP gen1 kit in ran a few times I hit the stop button 1 time now I cannot get 12v to ignition module. I traced it down to the MOM MOD but not sure how to test that. I rung the wire out to there then nothing and not sure what to do at this point. 5 miles on all brand new...

www.bigdogbiker.com

Sent from my Pixel 3a using Tapatalk

 

[mchllacey]

Check out this thread bith rip and esc use the same thunderheart unit. You can go to their support page for wiring diagrams

Rip Gen1 wire diagram

I have a 08 K9 put the RIP gen1 kit in ran a few times I hit the stop button 1 time now I cannot get 12v to ignition module. I traced it down to the MOM MOD but not sure how to test that. I rung the wire out to there then nothing and not sure what to do at this point. 5 miles on all brand new...

www.bigdogbiker.com

Sent from my Pixel 3a using Tapatalk

Thx I was not aware rip and ESC had the same pin out . I have the rip pin out.

Sent from my LGMP260 using Tapatalk

 

[mchllacey]

Do you have the Service Manual? Electrical is in Chapter 6. Compliments of bdm7250....

Manuals >>> https://www.dropbox.com/sh/4342373flodnbhj/AACDvhA93EOHPPKCs2gYPQDPa?dl=0anualsan
Like Reply

Yes I have the service manual , but thx . When I looked on deadlines site for info I thought it included wiring and this bike does have letters attached too wires and a ceramic head light fitting. On my other dog it did not have either one.

Sent from my LGMP260 using Tapatalk

 

[mchllacey]

Thx I was not aware rip and ESC had the same pin out . I have the rip pin out.

Sent from my LGMP260 using Tapatalk

Thx for the article link. Interesting read. I don't think this one has the MOM three inch box that is pictured in that article though.if it does it's hidden extremely well .lol

 

[pauldeepsea]

Sorry man, did you find what your looking for ?

 

[mchllacey]

Sorry man, did you find what your looking for ?

Yes I found what I needed.Thank you.
Now if I can borrow some brains to repair LOL

Sent from my LGMP260 using Tapatalk

 

[mchllacey]

Yes I found what I needed.Thank you.
Now if I can borrow some brains to repair LOL

Sent from my LGMP260 using Tapatalk

JK but this site is better than working at a large dealership, there's almost always somebody that's been through it or something similar. Thanks to all that contributed to this post. And this site in general.