turn signal, high beam, and horn not working

[mcip]

Hey all,

I'm hoping you can provide some suggestions. My 2006 K9 turn signals, high beam, and horn are not working. Bike starts and runs fine and the headlight and running lights light up normally. New battery. I'm at a loss.

Thanks!
Cip

 

[Matheny 514]

Welcome from Alabama. If you don't know if you have the original EHC, take a picture of the battery box area under the seat and post it so we can identify what you have.

 

[Brew]

Welcome from Washington State, hope you enjoy the site...

 

[mcip]

Yes, I have the original EHC. No problems so far, knock on wood!

I did check the headlight. Pulled the bulb and looked it over real good. No broken wires or dark spots.

 

[Th3InfamousI]

Need the bigger pic of your avatar before I can properly diagnose

Sent from my 831C using Tapatalk

 

[mcip]

Need the bigger pic of your avatar before I can properly diagnose

Sent from my 831C using Tapatalk

 

[HMAN]

If its only the fronts that don't work, I would look under the tank. Check for rubbed or pinched wires. Check the connectors themselves. Refill with dielectric grease if needed. Btw, nice pit crew.

 

[BWG56]

Need the bigger pic of your avatar before I can properly diagnose
Sent from my 831C using Tapatalk

Pig

View attachment 35230

Oh yeah, now that's what I'm talking about, what was your problem

I agree with HMAN, sounds like its the connector to the left hand control or the pcb on the left handle bar. Before you pull the tank, check the connector in the hand control.

 

[woodbutcher]

the horn could a problem all by itself. very prone to wires breaking. but then again you ain''t missin' much, it ain't nothin' but a squeak.


did you buy that scoot used from a guy named HOAT?????

 

[Th3InfamousI]

View attachment 35230

Thank-you!

Everything looks good there I have nothing to add ....everyone has covered the basics


Sent from my 831C using Tapatalk

 

[mcip]

If its only the fronts that don't work, I would look under the tank. Check for rubbed or pinched wires. Check the connectors themselves. Refill with dielectric grease if needed. Btw, nice pit crew.

Nope, HOAT still has his 2007 K9. Mine is an 06. I have a picture of our bikes together somewhere...will have to dig it up.

 

[mcip]

Thanks for all the advice Dogs! The tank is squeaking anyway so I'll pull it and take a look.

 

[woodbutcher]

if it is squeaking, check the vent tube in the fill-neck to see if it is broke.

so you know of the infamous HOAT ?

 

[Viking]

Squeaking tank, all the items not functioning operated from the same area, could it be more clear?

It is the harness under your tank.

Been there, done that. Donna used to have them in stock and it's a breeze to replace.

 

[Brew]

I think the squeak is coming from the hotness sitting on your seat. She left a wet spot, just dry it off...

 

[mcip]

Thanks all. I pulled the tank ... and scratched it of course @#$%^&*(!!
Some of the wires were getting frayed but not thru yet. Taped em up and added some foam tape under the tank to help with the squeaking. Pulled the controls apart and re-seated the electrical connections. All of the left side controls all work now. I'm still having trouble with the right side turn signal. I have 8v to all but the black wire at the connector when the key is on. PCB maybe? If so, where can I get one?

I'll keep putting pics up for incentive!

 

[BWG56]

Lets get a good look at those girls

 

[Little-Boo]

If you can get them beauties to pose like that you don't need our help to fix them lights.

Check wire harness between the connector and the turn signal housing it could a bad wire. Also make sure the JST connectors are plugged in and the wires didn't move or got pulled out from the JST connector.

Carlos