RubWhores 330 RidgeBack Project with Pitchers

[RubWhore]

OK here I go again I`m ready to go to the sandblaster and get started
So far I got the Frame,wheels rotors and pulley,Tins,a tranny with a bad mainshaft and a broke off bolt in the secondary gearset
a 124 S&S motor from an Ironhorsewith a bent rod a ripped up seat a wiring harness with melted plugs at the ehc
a leaking front end with bad bushings and three boxes of hand and foot control parts and dont let me forget the oil tank
I got tons of little stuff to find yet but thats the best part and
most fun of building so dig in your junk piles and PM me as I got a ton of parts to buy

 

[Mad Dog]

OK here I go again I`m ready to go to the sandblaster and get started
So far I got the Frame,wheels rotors and pulley,Tins,a tranny with a bad mainshaft and a broke off bolt in the secondary gearset
a 124 S&S motor from an Ironhorsewith a bent rod a ripped up seat a wiring harness with melted plugs at the ehc
a leaking front end with bad bushings and three boxes of hand and foot control parts and dont let me forget the oil tank
I got tons of little stuff to find yet but thats the best part and
most fun of building so dig in your junk piles and PM me as I got a ton of parts to buy

Sounds like you have matters well in hand.
If anybody can do it it's you Rub.
Good Luck.

 

[BBChopper]

WTF are you in production now????? How many a year????:2thumbs:

 

[RubWhore]

Will do Don
Im in pretty good on this one I figered with the sending the flywheels off
and all I shood be able to stay under 8000 cause most all the aluminum parts were throw aways from dealers I know and I gived 1200 bucks for the roller it was at a
insurance auction
this won was a 09 to start with Ive already started changing stuff
like I cut off the cheep lookig clutch cable rings and gonna put cable clamps
back on and beins I got boxes fulll of EHC`s I haint gonna go wire plus
most of the motor parts I got off eBAY already and LiLBoo solded me a liscence plate assembly so I hoping by spring to have this won done

WTF are you in production now????? How many a year????:2thumbs:

I reckon
only problem is I dont never sell any of em

:roll::roll::roll:

 

[BBChopper]

Will do Don
Im in pretty good on this one I figered with the sending the flywheels off
and all I shood be able to stay under 8000 cause most all the aluminum parts were throw aways from dealers I know and I gived 1200 bucks for the roller it was at a
insurance auction
this won was a 09 to start with Ive already started changing stuff
like I cut off the cheep lookig clutch cable rings and gonna put cable clamps
back on and beins I got boxes fulll of EHC`s I haint gonna go wire plus
most of the motor parts I got off eBAY already and LiLBoo solded me a liscence plate assembly so I hoping by spring to have this won done


I reckon
only problem is I dont never sell any of em

:roll::roll::roll:

Kracker!!!!:roll::roll::roll:

 

[RubWhore]

Kracker!!!!:roll::roll::roll:

What Can I say you got me

:roll::roll::roll::roll::roll::roll:

 

[TCALZ06]

Will do Don
Im in pretty good on this one I figered with the sending the flywheels off
and all I shood be able to stay under 8000 cause most all the aluminum parts were throw aways from dealers I know and I gived 1200 bucks for the roller it was at a
insurance auction
this won was a 09 to start with Ive already started changing stuff
like I cut off the cheep lookig clutch cable rings and gonna put cable clamps
back on and beins I got boxes fulll of EHC`s I haint gonna go wire plus
most of the motor parts I got off eBAY already and LiLBoo solded me a liscence plate assembly so I hoping by spring to have this won done

I need some of your connections. I would like to build a 330 too.
A new daytec frame is $2600

 

[RubWhore]

You are right cause I talked to Phil a while back bout one
I got this one from a Bank the guy bought it
coodnt pay for it so he stripped it and and stuckem
so the sent it to the auction for salvage
they were more than happy to unload it for anything
I been buying junk motorsickle parts for a long time
as my job takes me all over the South and you wood
not believe the stuff some of the stealers throw away
most of the BigDog stealers wood do insurance repairs
and if a part was scratched they wood throw it in a box
and save it for me when I passed threw I wood buy it by
the pound for aluminum usally the stuff just needing sanding
and repolishing frames they wood just replace if the powder got
scratched cause it was easier, just like motors I have been fortunate
enough to come across a bunch of motors threw the years
due to incompetent mechanics
I been doin this a long time so I got a lot of good connections
and thanks to Ebay I have been able to become an S&S dealer
Custom Chrome,Kustom Works,Drag as well as Midwest and Teds
cause I peddle my parts on there and keep my numbers up but I never
sell on here cause other folks were hear first and I respect and have made friends
with most all of them and you never no when you need a favor from any of them

:up::up:

 

[Nukeranger]

You're killing me! I sit here and procrastinate while you're living the dream. Good for you.

 

[TLB08K9]

WOW a whole day an no smart ass comments from Eric about something?????

Looks like you have it pretty well worked out there Rub. Can't wait to see how this one turns out!

 

[RubWhore]

Thats cause he haint hear no more

 

[lee]

looking good Rub - make sure you keep them pictures coming on the progress

 

[PA Chopper]

How come Eric got banned? Too bad...he had lots of good input.

 

[RubWhore]

Well Hmmmmm.....................
This is my build post not meaning to sound contrary
but you might PM one of the yellow dudes for that answer